Thursday, September 22, 2011

Uniden BC890XLT Discriminator Tap


Last week I bought a used Uniden BC890XLT scanner and added a discriminator audio tap.  Here's how I did it:
The first thing to do was open the case.  The outer sleeves come apart on the top and the bottom.  There are 2 screws on each side and one screw on the back that I removed.  I took both the top and bottom sleeves off to explore the inside, and discovered I only needed to remove the top to tap the discriminator audio.  Once inside I found the location of the discriminator audio which is pin #10 of IC #3, 3359DA.  Pin #10 is on the top right corner of the chip:








Rather than solder to the chip, I preferred to solder to the lead to the resistor at TP3 which is connected directly to PIN #10 of the IC.  I put a 10K ohm resistor in series with a 10 μF tantalum capacitor. 







 I wanted this modification to be removable so I didn't drill a hole in the case. Rather, I ran a connected wire to the outside of the case through an opening in the side of the case. 













I then ran the wire in the space between the case and the outer sleeve on the side.  I then ran it around the corner to the back of the scanner.  I connected the ground wire to the chassis via the screw that holds the accessory RCA jack.  I put heat shrink tubing on the outside of the wires and connected them to a 1/8" mono phone jack.  






Radio Shack Part Numbers:
1/4-Watt 10K ohm resistors - #271-1335
10μF Tantalum Capacitor - #272-1436
1/8" Mono In-line Phone Jack - #274-0333
Assorted Heat Shrink Tubes - #278-1627

Thursday, July 21, 2011

Saying goodbye to a good friend


It is hard to witness history as the Space Shuttle Program comes to an end. While I was never a direct participant in the program, I owe a lot to the Space Shuttle Program for who I am today.


I was four years old when Space Shuttle Columbia launched on STS-1 in 1981. I remember sitting with my parents in our living room watching on TV as the orbiter landed on the dry lakebed at Edwards Air Force base and thinking how cool it would be to be an astronaut and fly on a vehicle like that.


Days and years passed, and as much as I could, I would follow the Space Shuttle program through triumph and tragedy. I enjoyed classes and units at school on space and the U.S. space program. Hanging on the wall in my bedroom throughout elementary school, middle school, high school, and even part of college was this picture on a poster of the launch of STS-1 that I would look at when daydreaming of becoming an astronaut or a pilot.


In the end I chose a school and career path that led me to become an airline pilot, but the roots of my interest in science, math and aviation came from watching the Space Shuttle in all of it's power, majesty in ascent and grace on entry and landing. I hope that there is another vehicle to inspire my children to work hard to pursue their dreams.


So, farewell Columbia, Challenger, Discovery, Atlantis and Endeavour. I thank you. Fair winds and following seas.

Friday, June 17, 2011

Linear Birds



I was excited today to receive my new FT-857D to use on the linear birds. I realize the 857 will only provide half-duplex operation, but paired with my other handheld, it will be adequate. I'm looking forward to having additional passes available each day. I need to now work on some satellite antennas. Perhaps a couple of eggbeaters and a mounted yagi.

In a few days I should receive my 70cm preamp. I'm hoping it will allow me to hear birds like SO-50 that have only 500mW or less power output. It will be yet another set of satellite passes to work.

In light of the recent dire forecast of no sunspots for decades, I'll at least have one aspect of ham radio to still enjoy.

Duplex

So after over half a year of working the birds I finally pulled out an handheld receiver and worked AO-51 full duplex this afternoon. It was nice to actually hear my downlink and know that I was getting through. I guess I should've done this a long time ago. I need to figure out how to raise my audio level. I'm wondering if the hand microphone I've been using is very effective. It may be time to look for a replacement.

After finally getting some experience in tracking the satellites, I can focus on other areas of making my setup better. It's also ironic that the recent problems of AO-51 have actually made it easier to work it since the power output has been increased. I've now worked over 40 grid squares and am halfway to VUCC Satellite.

Wednesday, May 11, 2011

Aging Satellites



The past week there has been a lot of talk about AO-51 being offline. This has been my favorite satellite to work because it's been very easy. It's kind of sad to see it have issues, and just at a time when I have really gotten interested in working the birds as often as schedule allows.

I guess it's good to know now about the problems before I make a big investment in equipment to work satellites. I hope it can be successfully restored. If not, I hope that it's future replacement is launched sooner rather than later. I suppose I need to realize that traveling that high and fast in space put satellites in an extreme enviorment which makes for shorter rather than longer life expectancies.

Thursday, April 14, 2011

Yuri's Night


On April 12th I marked the 50th anniversary of the first human in space and the 30th anniversary of STS-1 by making some satellite contacts on AO-51 and an HF contact with R3K - a special event station from ARC Energia in Korolev, Russia (Russian Mission Control Center.) It's nice to dust off my arrow satellite antenna and make some new satellite contacts now that the weather is slowly getting warmer.

Wednesday, March 2, 2011

Got to see the final launch of Space Shuttle Discovery. It was neat to be a part of history. Here's a video I took of the launch.